Autocoder

L&T Technology Services interview questions

Last updated 2026-11-19

L&T Technology Services (LTTS) is an engineering and R&D services company, so its fresher interviews differ from a typical software-services process. Candidates commonly report questions from your branch fundamentals (electronics, computer science or mechanical, depending on the role) and, for software and embedded roles, C, microcontrollers, communication protocols and basic IoT.

This page works through that mix with worked answers. LTTS has not published a fixed fresher process that we can cite, so the rounds below are commonly reported. For the coding stage see LTTS coding round questions.

Work styleEngineering R&D services across product domains
Rounds (commonly reported)Online test, technical interview, HR interview
Frequent topicsC, embedded basics, protocols, OS, branch fundamentals

Rounds as commonly reported

Candidates describe an online assessment that mixes aptitude with technical questions from the branch and some programming, followed by a technical interview and an HR round. For embedded and software roles, the technical interview often begins with C and moves to microcontrollers, interrupts and protocols; for other branches it follows the core subjects.

Because LTTS projects are engineering product work, interviewers value understanding of how software meets hardware. Explaining your own embedded or electronics project in detail is the single most useful preparation.

Topics worth revising

Hiring status

There is no LTTS hiring page on this site and we hold no sourced LTTS statement on fresher numbers, dates or packages, so none are quoted. Check the LTTS careers site for current roles and eligibility.

L&T Technology Services interview questions: questions with worked answers

  1. 1

    What does the volatile keyword do in C, and when do you need it?

    medium

    volatile tells the compiler that a variable may change outside the normal flow of the program, so it must read it from memory on every access and not cache it in a register. Use it for memory-mapped hardware registers, variables modified in an interrupt service routine and read in the main loop, and shared flags. It does not make an operation atomic or thread safe.

  2. 2

    Explain the difference between UART, SPI and I2C.

    medium

    UART is asynchronous point-to-point serial using TX and RX with an agreed baud rate and no clock line. SPI is synchronous with a clock, MOSI, MISO and a chip-select per slave, is full duplex and fast, but uses more pins. I2C is synchronous with two wires, SDA and SCL, supports many devices by address, is slower and uses pull-up resistors. Choose by speed, pin count and number of devices.

  3. 3

    What is an interrupt, and what should an interrupt service routine avoid?

    medium

    An interrupt is a hardware or software signal that makes the CPU pause the main program, run an ISR and then resume. ISRs should be short and fast: avoid blocking calls, long loops, dynamic memory allocation and slow printing. Set a flag or push data into a buffer and process it in the main loop. Shared variables need volatile and, if wider than the bus, protection against partial reads.

  4. 4

    What is the difference between a process and a thread, and what is an RTOS?

    medium

    A process has its own address space while threads inside it share memory. A real-time operating system schedules tasks to meet deadlines predictably, typically with priority-based pre-emptive scheduling and bounded interrupt latency. The key measure is determinism, not speed. Examples include FreeRTOS and Zephyr. Used where missing a deadline causes failure, such as control systems.

  5. 5

    What is priority inversion and how is it solved?

    hard

    Priority inversion occurs when a high-priority task waits for a mutex held by a low-priority task that is itself pre-empted by a medium-priority task, so the high-priority task is effectively delayed by the medium one. Solutions include priority inheritance, where the lock holder temporarily takes the waiter priority, and priority ceiling protocols. It famously affected a Mars rover mission in 1997.

  6. 6

    Explain structure padding in C with an example.

    medium

    Compilers insert unused bytes between structure members so that each is aligned to its natural boundary, which the CPU accesses efficiently. For struct { char a; int b; char c; } on a typical 32-bit-aligned platform the size is 12, not 6: 3 bytes pad after a, and 3 after c. Reordering members from largest to smallest reduces padding. #pragma pack removes it at the cost of slower or unsupported unaligned access.

  7. 7

    What is the difference between const char *p, char * const p and const char * const p?

    medium

    Read declarations right to left. const char *p means p points to a constant char: you can move the pointer but not change the data. char * const p means a constant pointer to a char: you can change the data but not repoint. const char * const p means neither can change. Mixing them up is a common C interview trap.

  8. 8

    How do you debounce a mechanical switch?

    medium

    Mechanical contacts bounce for a few milliseconds, producing several transitions. Hardware debouncing uses an RC filter or a Schmitt trigger. In software, ignore changes until the input has been stable for a set time, for example sample every few milliseconds and accept a new state after several consecutive identical readings, or start a timer on the first edge and re-read after about 10 to 20 ms.

  9. 9

    What is the watchdog timer?

    easy

    A watchdog is a hardware timer that resets the microcontroller if the software does not periodically reset (kick) it within a timeout, recovering from hangs or infinite loops. Kick it only from a place that proves the main logic is healthy, not from an interrupt that keeps running while the main loop is stuck. It is a standard safety feature in embedded products.

  10. 10

    What is IoT, and how would you design a simple temperature-monitoring system?

    medium

    IoT connects physical devices to networks to collect and act on data. A simple design: a sensor reads temperature through an ADC or digital interface on a microcontroller, which sends readings over Wi-Fi or another link using a lightweight protocol such as MQTT to a broker and a cloud dashboard, with alerts above a threshold. Discuss power use, security (authentication, encryption) and what happens when the network is down.

  11. 11

    Walk me through your final-year project, and how did you test it?

    medium

    Cover the goal, block diagram, the hardware and software split, your own part and the testing: unit tests, bench tests with instruments, edge cases such as power loss. Be ready for questions on every component and every line of code you wrote. Engineering interviewers prefer honest limitations over polished claims.

  12. 12

    Why LTTS, and are you comfortable with a role that may not match your preferred branch?

    easy

    Link your answer to engineering and R&D work across product domains and to a project you did. On flexibility, answer honestly: some roles are in embedded, some in software and some in mechanical or testing. Show interest in learning and give an example of picking up a skill outside your main branch.

Frequently asked questions

Does LTTS ask coding questions?

Commonly reported at a basic to medium level, often in C or C++ for embedded roles, plus aptitude and technical MCQs.

Which branches does LTTS hire from?

We hold no sourced information on current eligibility. Check the listing on the LTTS careers site.

What is the most important topic for embedded roles?

C fundamentals, including pointers and volatile, and microcontroller basics such as interrupts and protocols.

Is the HR round difficult?

Generally about motivation, flexibility and communication. Prepare honest answers.

Where do I find official openings?

On the L&T Technology Services careers site.

Related guides

More in Company Interview Questions

See all in this section